ITI Fitter Free Mock Test : Semeser 1 - Module 1 - Basic Fitting

Created on May 10, 2025

ITI Fitter

ITI Fitter Free Mock Test - Semester 1 : Basic Fitting

Fitter : Semester 1 : Basic Fitting (146 Questions)

Name

1 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the accuracy of metric outside
micrometer?

A) 0.01 mm

B) 0.001 mm

C) 0.02 mm

D) 0.002 mm

2 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reading of vernier bevel protractor?

A) 18° 50’

B) 41° 50 ‘

C) 50°50 ‘

D) 58° 50’

3 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of gauge?

A) Bevel gauge

B) Angle gauge

C) Surface gauge

D) Universal bevel gauge

4 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of portion left between
flutes in a drill?

A) Lip

B) Web

C) Point

D) Shank

5 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of the vice?

A) Pin vice

B) Pipe vice

C) Hand vice

D) Quick releasing vice

6 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part of file marked as x .

A) Tang

B) Ferrule

C) File length

D) Heel

7 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reading of an outside micrometer (British)?

A) 0.309

B) 0.329

C) 0.359

D) 0.36

8 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the part marked as x in pedestal grinder?

A) Tool rest

B) Eye shield

C) Wheel guard

D) Grinding wheel

9 / 146

Category: Fitter Sem 1 : Basic Fitting

Which hacksaw blade is used for cutting
along curved lines?

A) HSS blade

B) All hard blade

C) Flexible blade

D) Diamond blade

10 / 146

Category: Fitter Sem 1 : Basic Fitting

Which activity causes excessive wear and
chattering of drill bit while drilling?

A) Too fast feed rate

B) Too slow feed rate

C) More cutting speed

D) Too slow spindle speed

11 / 146

Category: Fitter Sem 1 : Basic Fitting

Which chisel is used to remove excess
metal from welded joint and castings?

A) Flat chisel

B) Web chisel

C) Cross cut chisel

D) Half round chisel

12 / 146

Category: Fitter Sem 1 : Basic Fitting

How the drill chucks are held on the
machine spindle?

A) By arbor

B) By sockets

C) By sleeves

D) By special clamp

13 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the use of bevel protractor?

A) Check the length

B) Set the work piece

C) Measure the angle

D) Measure the depth

14 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the unit of feed in drilling
operation?

A) m/rev

B) mm/rev

C) m/min

D) mm/min

15 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the minor diameter of thread?

A) Minor dia = Major dia – (2 x pitch)

B) Minor dia = Major dia + (2 x pitch)

C) Minor dia = Major dia + (2 x depth)

D) Minor dia = Major dia – (2 x depth)

16 / 146

Category: Fitter Sem 1 : Basic Fitting

Convert one metre into millimetre.

A) 10 mm

B) 100 mm

C) 1000 mm

D) 10000 mm

17 / 146

Category: Fitter Sem 1 : Basic Fitting

Which chisel is used for cutting curved
grooves?

A) Flat chisel

B) Web chisel

C) Cross cut chisel

D) Half round nose chisel

18 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part marked X in hammer?

A) Pein

B) Face

C) Cheek

D) Eye hole

19 / 146

Category: Fitter Sem 1 : Basic Fitting

Which part of universal surface gauge holds
the scriber?

A) Snug

B) Guide pin

C) Rocker arm

D) Fine adjustment screw

20 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part marked as x .

A) Leg

B) Peg

C) Washer

D) Fulcrum

21 / 146

Category: Fitter Sem 1 : Basic Fitting

How to prevent the tool rubbing against
the work surface in metal cutting process?

A) Decrease lip angle

B) Increased rake angle

C) Increase clearance angle

D) Decrease tool wedge angle

22 / 146

Category: Fitter Sem 1 : Basic Fitting

Identify the type of V blocks?

A) Single level single groove

B) Single level double groove

C) Double level single groove

D) Double level double groove

23 / 146

Category: Fitter Sem 1 : Basic Fitting

Which metal cutting saw is used to cut
large cross section area?

A) Power saw

B) Contour saw

C) Circular saw

D) Horizontal band saw

24 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part of a hammer marked as x .

A) Face

B) Pein

C) Cheek

D) Eye hole

25 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of part marked as x in drilling machine?

A) Drill chuck

B) Feed handle

C) Driving motor

D) Depth gauge and stop

26 / 146

Category: Fitter Sem 1 : Basic Fitting

Why the cutting faces of files are slightly
bellied on length wise?

A) Get proper grip over workpiece

B) Filing flat surfaces is made easier

C) Permit clearance between file face and the workpiece

D) Ensure more pressure on workpiece while filing

27 / 146

Category: Fitter Sem 1 : Basic Fitting

Which type of taper is provided in the drill
shank?

A) Pin taper

B) Metric taper

C) Morse taper

D) Jerno taper

28 / 146

Category: Fitter Sem 1 : Basic Fitting

Which marking media is poisonous?

A) White wash

B) Prussian blue

C) Copper sulphate

D) Cellulose lacquer

29 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of the part marked as X ?

A) Spindle

B) Sleeve

C) Thimble

D) Spindle lock

30 / 146

Category: Fitter Sem 1 : Basic Fitting

Which type of screw threads are rounded
at the crest and root?

A) B.A thread

B) B.S.F thread

C) B.S.W thread

D) ACME thread

31 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reading of vernier caliper?

A) 30.20mm

B) 30.40mm

C) 35.20mm

D) 35.50mm

32 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of hammer?

A) Mallet hammer

B) Ball pein hammer

C) Cross pein hammer

D) Straight pein hammer

33 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the purpose of Crowning on the
cutting edge of chisel?

A) Prevent slipping of chisel

B) Prevent digging of corners

C) Allow chisel to move freely on straight line

D) Allow cutting edge to penetrate into the work

34 / 146

Category: Fitter Sem 1 : Basic Fitting

Why surface plates are made of stress
relieved good quality cast iron?

A) To prevent corrosion

B) To prevent breaking

C) To prevent distortion

D) To prevent thermal expansion

35 / 146

Category: Fitter Sem 1 : Basic Fitting

Which is an integral part of the stock in vernier bevel protractor?

A) Disc

B) Dial

C) Blade

D) Main scale

36 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the property of metal to resist the
effect of tensile forces without rupture.

A) Ductility

B) Tenacity

C) Elasticity

D) Malleability

37 / 146

Category: Fitter Sem 1 : Basic Fitting

Which chisel is used for cutting oil grooves?

A) Flat chisel

B) Web chisel

C) Half round nose chisel

D) Diamond point chisel

38 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the use of feeler gauge?

A) Check the width

B) Check the height

C) Check the length

D) Check the gap between the mating parts

39 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of the part marked as x in combination set?

A) Rule

B) Scriber

C) Clamp nut

D) Spirit level

40 / 146

Category: Fitter Sem 1 : Basic Fitting

Which part of the vernier height gauge is
an intergral part of the main slide?

A) Jaw

B) Base

C) Beam

D) Jaw clamp

41 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of file?

A) Rotary file

B) Tinkers file

C) Barrette file

D) Crossing file

42 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the defect that causes the metal chips
to clog between the teeth of file?

A) File bite

B) Pinning of file

C) Warping of file

D) Glazing of file

43 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the main advantage of adjustable
parallel block?

A) To set different angle

B) To set different depth

C) To set different length

D) To set different height

44 / 146

Category: Fitter Sem 1 : Basic Fitting

Which caliper provide fine adjustment of
dimensions?

A) Inside caliper

B) Odd leg caliper

C) Outside caliper

D) Spring joint caliper

45 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of part marked as x in combination set?

A) Bevel head

B) Centre head

C) Square head

D) Protractor head

46 / 146

Category: Fitter Sem 1 : Basic Fitting

Which caliper is used to mark the centre of
round bar?

A) Jenny caliper

B) Inside caliper

C) Outside caliper

D) Firm joint caliper

47 / 146

Category: Fitter Sem 1 : Basic Fitting

Which vice is used for holding hollow
cylindrical jobs?

A) Pin vice

B) Pipe vice

C) Hand vice

D) Bench vice

48 / 146

Category: Fitter Sem 1 : Basic Fitting

What happen if the clearance angle of chisel
is too high?

A) Slipping of chisel

B) Digging on the surface

C) Cutting edge will break

D) Heavy metal removal from the surface

49 / 146

Category: Fitter Sem 1 : Basic Fitting

Which part is the measuring face fitted to
the frame of outside micrometer?

A) Anvil

B) Barrel

C) Spindle

D) Ratchet stop

50 / 146

Category: Fitter Sem 1 : Basic Fitting

What will be the effect if the clearance angle
of chisel is less than recommended angle while
chipping?

A) Cutting edge cannot penetrate, chisel will slip

B) Cutting edge digs in, cut will be deeper

C) Cutting edge will break

D) Cutting edge of chisel move freely on straight line

51 / 146

Category: Fitter Sem 1 : Basic Fitting

Which is used for filling narrow grooves and
angles above 10°?

A) Square file

B) Half round file

C) Triangular file

D) Knife edge file

52 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the pitch of hacksaw blade used to
cut conduit and other thin tubes?

A) 0.8mm

B) 1.0mm

C) 1.4mm

D) 1.8mm

53 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of the vice?

A) Hand vice

B) Bench vice

C) Tool maker s vice

D) Quick releasing vice |

54 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part marked as x of the file.

A) Heel

B) Edge

C) Ferrule

D) Shoulder

55 / 146

Category: Fitter Sem 1 : Basic Fitting

Which grinding machine is used for heavy
duty work?

A) Bench grinder

B) Portable grinder

C) Pedestal grinder

D) Surface grinder

56 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the accuracy of a try square?

A) 0.02 mm per 10 mm length

B) 0.004 mm per 10 mm length

C) 0.002 mm per 10 mm length

D) 0.001 mm per 10 mm length

57 / 146

Category: Fitter Sem 1 : Basic Fitting

Which punch is used for witness marks?

A) Dot punch

B) Pin punch

C) Bell punch

D) Centre punch

58 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the angular measuring instrument

A) Bevel gauge

B) Bevel protractor

C) Universal bevel gauge

D) Universal surface gauge

59 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of angle between the
axis of chisel and job surface while chipping?

A) Rake angle

B) Point angle

C) Clearance angle

D) Angle of inclination

60 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reading of the outside micrometer 50 to 75mm?

A) 63.63 mm

B) 63.00 mm

C) 63.36 mm

D) 63.13 mm

61 / 146

Category: Fitter Sem 1 : Basic Fitting

Why the hand taps are chamfered at the
lead?

A) Aligning

B) Finishing

C) Strengthening

D) Gripping

62 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of tap wrench?

A) Box type tap wrench

B) Solid type tap wrench

C) T Handle tap wrench

D) Adjustable tap wrench

63 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the formula to calculate tap drill
size?

A) Tap drill size = Major dia – (2 x depth)

B) Tap drill size = Major dia + (2 x depth)

C) Tap drill size = Major dia – (2 + depth)

D) Tap drill size = Major dia + (2 + depth)

64 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of part marked as x in drill?

A) Land

B) Flank

C) Web

D) Lip

65 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of the part marked as X ?

A) Beam

B) Main scale

C) Fine adjusting nut

D) Fine adjusting slide

66 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of vice?

A) Pin vice

B) Pipe vice

C) Hand vice

D) Machine vice

67 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part marked as x in depth micrometre.

A) Cap

B) Lock

C) Stock

D) Thimble

68 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the use of a try square?

A) To check right angle

B) To check acute angle

C) To check obtuse angle

D) To check straight angle

69 / 146

Category: Fitter Sem 1 : Basic Fitting

Which file has the parallel edges throughout
the length?

A) Hand file

B) Bastard file

C) Rasp cut file

D) Single cut file

70 / 146

Category: Fitter Sem 1 : Basic Fitting

Where will be the weight of the hammer
stamped?

A) Face

B) Pein

C) Cheek

D) Eye hole

71 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of operation?

A) Marking line at 90°

B) Checking flatness

C) Checking squareness

D) Setting work piece at right angle

72 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part marked as x .

A) Anvil

B) Thimble

C) Spindle

D) Spindle lock

73 / 146

Category: Fitter Sem 1 : Basic Fitting

How much carbon content of steel is
forgeable?

A) Up to 1.2 %

B) Up to 1.7 %

C) Up to 1.9 %

D) Up to 2.1 %

74 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of file?

A) Hand file

B) Rasp cut file

C) Single cut file

D) Curved cut file

75 / 146

Category: Fitter Sem 1 : Basic Fitting

A new hacksaw blade after a few stroke,
becomes loose because of?

A) stretching of blade

B) wrong pitch of the blade

C) improper selection of saw sets

D) nut thread being worn out

76 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the unit of cutting speed in drilling
operation?

A) m/ rev

B) mm/ rev

C) m/ min

D) mm/ min

77 / 146

Category: Fitter Sem 1 : Basic Fitting

What operation is carried out in a gang
drilling machine?

A) Idle operation

B) Repeated operation of drilling

C) Continuous milling operation

D) Successive operation of drilling

78 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of the part marked as X ?

A) Tip

B) Heel

C) Tang

D) Safe edge

79 / 146

Category: Fitter Sem 1 : Basic Fitting

Read the measurement in the dial caliper.

A) 24.2 mm

B) 24.8 mm

C) 25.2 mm

D) 26.2 mm

80 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the principle of micrometer?

A) Sliding

B) Screw and nut

C) Rack and pinion

D) Worm and worm wheel

81 / 146

Category: Fitter Sem 1 : Basic Fitting

In the ISO metric thread, calculate the tap
drill size for M 10 x 1.5 thread.

A) 8.2 mm

B) 8.7 mm

C) 8.75 mm

D) 8.65 mm

82 / 146

Category: Fitter Sem 1 : Basic Fitting

Which chisel is used for cutting keyways?

A) Cross cut chisel

B) Punching chisel

C) Diamond point chisel

D) Flat chisel

83 / 146

Category: Fitter Sem 1 : Basic Fitting

Which pitch of blade is used for cutting
bronze, brass and cast iron?

A) 0.80 mm

B) 1.00 mm

C) 1.40 mm

D) 1.80 mm

84 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the file shown.

A) Riffler file

B) Tinkers file

C) Barrette file

D) Crossing file

85 / 146

Category: Fitter Sem 1 : Basic Fitting

Which drilling machine, the spindle head is
moved towards or away from the column?

A) Pillar drilling machine

B) Gang drilling machine

C) Radial drilling machine

D) Sensitive bench drilling machine

86 / 146

Category: Fitter Sem 1 : Basic Fitting

Which chisel used for squaring materials at
the corners, joints?

A) Flat chisel

B) Cross cut chisel

C) Diamond point chisel

D) Half round nose chisels

87 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of angle marked a in chisel?

A) Rake angle

B) Wedge angle

C) Cutting angle

D) Clearance angle

88 / 146

Category: Fitter Sem 1 : Basic Fitting

Which type of hammer is used for riveting
purpose?

A) Sledge hammer

B) Ball pein hammer

C) Cross pein hammer

D) Straight pein hammer

89 / 146

Category: Fitter Sem 1 : Basic Fitting

What happens if the vice handle is over
tightened?

A) Spindle damage

B) Hard jaw damage

C) Fixed jaw damage

D) Movable jaw damage

90 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the property of metal that withstand
shock or impact?

A) Tenacity

B) Hardness

C) Brittleness

D) Toughness

91 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the use of fine pitch hacksaw
blades?

A) To cut soft metal

B) To cut high speed steel

C) To cut high carbon steel

D) To cut conduit and other thin tubes

92 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of the caliper having one
leg with an adjustable divider point and other leg is
bent?

A) Jenny caliper

B) Inside caliper

C) Outside caliper

D) Spring joint caliper

93 / 146

Category: Fitter Sem 1 : Basic Fitting

Which type of datum is followed?

A) Edge datum

B) Point datum

C) Centre line datum

D) Reference line datum

94 / 146

Category: Fitter Sem 1 : Basic Fitting

Which file is used for manufacturing of dies
and moulds?

A) Rotary file

B) Tinkers file

C) Barrette file

D) Rasp cut file

95 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the method of removing metal
chips clogged between the teeth of files?

A) Brush

B) Wire brush

C) Copper strip

D) Chalk powder

96 / 146

Category: Fitter Sem 1 : Basic Fitting

Which file is used for sharpening the teeth
of wood working saws?

A) Barrete file

B) Tinker s file

C) Millsaw file

D) Riffler file

97 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the material to manfacture bench
vice?

A) Tool steel

B) High carbon steel

C) Medium carbon steel

D) Cast iron

98 / 146

Category: Fitter Sem 1 : Basic Fitting

Which caliper is used to find the centre of
round bars?

A) Inside caliper

B) Jenny caliper

C) Vernier caliper

D) Outside caliper

99 / 146

Category: Fitter Sem 1 : Basic Fitting

Which marking media provide clear lines on
machine finished surfaces?

A) White wash

B) Prussian blue

C) Copper sulphate

D) Cellulose lacquer

100 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reading of vernier caliper with inch graduations?

A) 1.068

B) 1.459

C) 1.418

D) 1.409

101 / 146

Category: Fitter Sem 1 : Basic Fitting

Calculate the tap drill size for M10 x 1.25.

A) 8.8 mm

B) 8.7 mm

C) 8.75 mm

D) 8.65 mm

102 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the property of metal which can be
drawn into wire without rupture.

A) Ductility

B) Tenacity

C) Elasticity

D) Malleability

103 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the accuracy of protractor head in
combination set?

A) 1°

B) 5°

C) 5’

D) 5”

104 / 146

Category: Fitter Sem 1 : Basic Fitting

Which part of combination set is used to
mark and check angle of 90° and 45°?

A) Rule

B) Centre head

C) Square head

D) Protractor head

105 / 146

Category: Fitter Sem 1 : Basic Fitting

Which vice is used for holding small work
that requires filing or drilling?

A) Pin vice

B) Pipe vice

C) Hand vice

D) Tool maker s vice

106 / 146

Category: Fitter Sem 1 : Basic Fitting

Which part of universal surface gauge is
used to set scriber at required position exactly?

A) Snug

B) Guide pin

C) Rocker arm

D) Fine adjustment screw

107 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of parallel block?

A) Solid parallel block

B) Tenon parallel block

C) Angular parallel block

D) Adjustable parallel block

108 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the property of metal that permits
no permanent distortion before breaking?

A) Tenacity

B) Hardness

C) Brittleness

D) Toughness

109 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the spindle movement of one
division of thimble with spindle thread of 0.5mm
pitch?

A) 0.01 mm

B) 0.10 mm

C) 1.00 mm

D) 10.0 mm

110 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of V block?

A) V grooved V block

B) Single level single groove V block

C) Double level single groove V block

D) Single level double groove V block

111 / 146

Category: Fitter Sem 1 : Basic Fitting

Which chisel is used for removing materials
on the corners of the keyways?

A) Flat chisel

B) Diamond point chisel

C) Cross cut chisel

D) Half round nose chisel

112 / 146

Category: Fitter Sem 1 : Basic Fitting

Which angle is represented by the symbol g on the cutting chisel?

A) Rake angle

B) Wedge angle

C) Cutting angle

D) Clearance angle

113 / 146

Category: Fitter Sem 1 : Basic Fitting

Why ribs are provided in the angle plate?

A) Provide flatness

B) Prevent distortion

C) Provide squareness

D) Support the machined surface

114 / 146

Category: Fitter Sem 1 : Basic Fitting

Which material is used to manufacture
grade A V blocks?

A) Tool steel

B) Carbon steel

C) High quality steel

D) Closely grained cast iron

115 / 146

Category: Fitter Sem 1 : Basic Fitting

Which file is used for filing wood and
leather?

A) Hand file

B) Bastard file

C) Rasp cut file

D) Single cut file

116 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the purpose of slots provided in the
slotted angle plate?

A) Job clamping

B) Easy handling

C) Reduce weight

D) Better appearance

117 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of part marked as x in surface gauge?

A) Nut

B) Snug

C) Spindle

D) Scriber

118 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the file.

A) Barrot file

B) Riffler file

C) Crossing file

D) Mill saw file

119 / 146

Category: Fitter Sem 1 : Basic Fitting

Which part of outside micrometer ensure a
uniform pressure between the measuring surface?

A) Anvil

B) Thimble

C) Spindle lock

D) Ratchet stop

120 / 146

Category: Fitter Sem 1 : Basic Fitting

Which file is having rows of teeth cut in one
direction?

A) Single cut file

B) Curved cut file

C) Second cut file

D) Double cut file

121 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the effect of improper method of
diagonal filing?

A) Uneven surface finish

B) Scratches on the surface

C) Convexity on the surface

D) Improper finish on surface

122 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part marked as x .

A) Lip

B) Land

C) Flank

D) Point angle

123 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of micrometer?

A) Depth micrometer

B) Inside micrometer

C) Vernier micrometer

D) Outside micrometer

124 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the part marked as x in vernier caliper.

A) Beam

B) Fixed bar

C) Depth bar

D) Thumb lever

125 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reading in inch micrometer?

A) 0.789

B) 0.787

C) 0.783

D) 0.715

126 / 146

Category: Fitter Sem 1 : Basic Fitting

Which part in drilling machine is to achieve
different speed?

A) Flat pulley

B) Jockey pulley

C) Stepped pulley

D) Fast and loose pulley

127 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reading of vernier bevel protractor?

A) 27°30’

B) 67° 30’

C) 157° 30’

D) 159° 30’

128 / 146

Category: Fitter Sem 1 : Basic Fitting

Which marking media is applied to rough
forgings and castings?

A) White wash

B) Prussian blue

C) Copper sulphate

D) Cellulose lacquer

129 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reason for scratches produced
on filed surface?

A) Pinning

B) Glazing

C) File bite

D) Warping

130 / 146

Category: Fitter Sem 1 : Basic Fitting

Which file is used to make the job close to
the finishing size?

A) Single cut file

B) Curved cut file

C) Second cut file

D) Double cut file

131 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the weight of hammer used for
marking purpose?

A) 200 grams

B) 250 grams

C) 300 grams

D) 450 grams

132 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the accuracy of Vernier bevel
protractor?

A) 1°

B) 5°

C) 5’

D) 5 “

133 / 146

Category: Fitter Sem 1 : Basic Fitting

Which metal cutting saw is used for cutting
different profiles?

A) Power saw

B) Circular saw

C) Contour band saw

D) Horizontal band saw

134 / 146

Category: Fitter Sem 1 : Basic Fitting

Which chisel is used for separating materials
after chain drilling?

A) Web chisel

B) Flat chisel

C) Cross cut chisel

D) Diamond point chisel

135 / 146

Category: Fitter Sem 1 : Basic Fitting

Why chalk is applied on the face of the file?

A) To reduce excessive pressure

B) To increase chip removed rate

C) To reduce penetration and pinning

D) To increase penetration and pinning

136 / 146

Category: Fitter Sem 1 : Basic Fitting

Why breakage of teeth occur easily while
sawing of thin walled work pieces and the start of
cut?

A) Hand force is too big

B) Cutting section is too short

C) Coarse blade to be used

D) Hand force acts only upon few teeth

137 / 146

Category: Fitter Sem 1 : Basic Fitting

Why slight convexity is given on the face of
hammer?

A) To make effective striking

B) To avoid digging of the edge

C) To allow even load on striking

D) To prevent damage to work surface

138 / 146

Category: Fitter Sem 1 : Basic Fitting

Which is used to remove drills and sockets
from the machine spindle?

A) Drift

B) Sleeve

C) Punch

D) Hammer

139 / 146

Category: Fitter Sem 1 : Basic Fitting

Which part of the bevel protractor contact
with the inclined surface while measuring?

A) Dial

B) Disc

C) Blade

D) Stock

140 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of drilling machine?

A) Pillar drilling machine

B) Gang drilling machine

C) Bench drilling machine

D) Radial drilling machine

141 / 146

Category: Fitter Sem 1 : Basic Fitting

How the wide range of depth can be
measured by depth micrometer?

A) Lengthy sleeve

B) Lengthy spindle

C) Adjustable base

D) Equipped with a set of extension rods

142 / 146

Category: Fitter Sem 1 : Basic Fitting

Why marking tables are made up of cast
iron?

A) Self lubricating

B) Make more rigidity

C) Maintain the accuracy

D) Prevent thermal expansion

143 / 146

Category: Fitter Sem 1 : Basic Fitting

Which is used to finish the resharpened
divider point?

A) File

B) Grinder

C) Scraper

D) Oil stone

144 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the reading of a vernier caliper?

A) 35.1 mm

B) 35.2 mm

C) 35.3 mm

D) 35.4 mm

145 / 146

Category: Fitter Sem 1 : Basic Fitting

Name the tap wrench used in the restricted
place.

A) Box type tap wrench

B) T handle tap wrench

C) Solid type tap wrench

D) Double ended adjustable tap wrench

146 / 146

Category: Fitter Sem 1 : Basic Fitting

What is the name of chisel?

A) Flat chisel

B) Web chisel

C) Cross cut chisel

D) Diamond point chisel

Your score is

The average score is 0%

0%

ITI Fitter Free Mock Test : Semeser 1 – Module 1 – Basic Fitting

Popular Posts

EDITOR PICKS

JUNIOR INSTRUCTOR (INFORMATION COMMUNICATION TECHNOLOGY SYSTEM MAINTENANCE Test Series

2025 വർഷത്തെ ഐ ടി ഐ പ്രവേശനത്തിന് അപേക്ഷ ക്ഷണിച്ചു

54th Kerala Film Award 2024- Mock Test

POPULAR POSTS

JUNIOR INSTRUCTOR (INFORMATION COMMUNICATION TECHNOLOGY SYSTEM MAINTENANCE Test Series

2025 വർഷത്തെ ഐ ടി ഐ പ്രവേശനത്തിന് അപേക്ഷ ക്ഷണിച്ചു

54th Kerala Film Award 2024- Mock Test

POPULAR CATEGORY

ABOUT US

FOLLOW US